ZyXEL omni.net LCD+M Manuel d'utilisateur Page 57
- Page / 186
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Technical Reference for ZyXEL omni.net series
4-9
If an incoming SETUP message is offered with addressing information (i.e. the appropriate part of
the called_party_number), this address will be compared with the MSN numbers assigned by the
[AT&ZIn=s] commands. The call will be accepted using the specific protocol, if the assigned
number of this protocol matches the received called party number.
NOTE: You are not required to enter the complete number string for
the [AT&Zin] command. The last few distinguishable digits will be
enough for the Omni.net to make the decision. Two phone number
strings are said to be matched if their least significant 'n' digit(s) are
identical, where 'n' is the number of digits in the shorter string.
Called_Party_Subaddress information within the incoming SETUP message can also be used to
select the protocols and/or analog ports. In normal conditions Called_Party_Subaddress
information is not used by the omni.net to select the protocols or services, but only indicates the
subaddress (if any) to the DTE.
- ISDN Terminal Adapters 2
- Limited Warranty 3
- Become a Registered Owner 3
- Contents 5
- PART II ISDN FUNCTION 6
- PART III VOICE FEATURES 7
- PART IV DATA FUNCTION 8
- PART V FAX/MODEM FUNCTION 9
- PART VII APPENDICES 10
- Content of Tables 13
- Content of Figures 17
- Preface 18
- How to Use This Manual 19
- Other References 19
- Part I 21
- Introduction 21
- Chapter 1 23
- Intelligent Features 24
- Specifications 24
- Key Features Summary 25
- Chapter 2 27
- ISDN Configuration Manager 27
- Bumping 31
- Configuring ISDN Parameters 32
- Chapter 3 33
- LCD/LCD+M) 33
- LCD Panel Functions 34
- Right key: 35
- Left key: 35
- Up key: 35
- Down key: 35
- Idle Screen 36
- Set Clock sub-menu 36
- Set Display Mode sub-menu 36
- Dial In Log 37
- Stored Phone List 37
- Dial Out Log 38
- Active Status 39
- Clock Options 40
- Update Clock 41
- Set Display Mode 42
- Dial In Log Options 43
- button 44
- Dial Out Log Options 45
- Part II 47
- ISDN Function 47
- Chapter 4 49
- ISDN Communication Basics 49
- Supported AT Command Types 51
- LCD/LCD+M/Plus) 54
- Placing a Data Call 55
- Incoming Calls 55
- Command Description 58
- ATS119.3=0 58
- ATS119.3=1 58
- Best effort call answering 58
- Part III 61
- Voice Features 61
- Supplementary Service 63
- Chapter 5 63
- Call Waiting 64
- Call Hold/Retrieve 64
- Three Way Conferencing 66
- Starting a conference call 66
- Call Forwarding 68
- For DSS1 switch 68
- Chapter 6 71
- Feature Phone Operation 71
- Flash Key Commands 72
- InterCom 72
- Receiving a Second Call 73
- Call Broker 74
- Call Reject 75
- Call Transfer 75
- Three-Way Conference Call 76
- Last Number Redial 77
- Quick Dial 77
- Part IV 79
- Data Function 79
- Chapter 7 81
- Feature List 82
- Async to Sync Conversion 82
- Authentication Conversion 82
- Multilink PPP 84
- Call Bumping 84
- Bandwidth On Demand (BOD) 86
- BACP/BAP 86
- Chapter 8 89
- ISDN Communications 89
- V.110 Outgoing Protocol 91
- V.120 Outgoing Protocol 92
- X.75 Outgoing Protocol 93
- Speeds of 128Kbps 95
- V.120 Bundled Call 95
- X.75 Bundled Call 97
- Table 52. V.42bis AT Command 98
- Data Compression with X.75 100
- Security Settings 101
- Modifying the User Passwords 105
- Password: 106
- Part V 107
- Fax/Modem Function 107
- Chapter 9 109
- Internal Fax/Modem Function 109
- MNP Protocols 110
- Xmodem, Ymodem, and Zmodem 110
- Fax and Facsimile 111
- Modem as a fax 111
- EIA Class 1 Fax Commands 111
- Answering a Call Using MSN 113
- Control Data Compression 115
- Fax Operation 115
- Fax Command Sets 116
- Appendix D) 118
- Part VI 119
- Diagnostics 119
- Firmware Update 119
- Chapter 10 121
- Power-on Self-test 122
- Resetting Your omni.net 124
- Capturing the Protocol Data 125
- Analyzing the Captured Data 126
- Chapter 11 129
- Firmware Upgrade 129
- Kernel Mode 130
- Part VII 133
- Appendices 133
- Appendix A 135
- AT Command Set Reference 135
- AT Commands Description 136
- AT Commands Prefix (AT) 136
- Description of ATI3 Output 144
- Fax Command 151
- Appendix B 153
- Setting S-registers 154
- S-Register Descriptions 156
- Appendix C 181
- Appendix D 183
- Serial Port Interface 183
Produits connexes et manuels pour Modems ZyXEL omni.net LCD+M
Modems ZyXEL 3356P Manuel d'utilisateur
(30 pages)
(30 pages)
Modems ZyXEL P841C Manuel d'utilisateur
(41 pages)
(41 pages)
Modems ZyXEL P-660M Manuel d'utilisateur
(2 pages)
(2 pages)
Modems ZyXEL ADSL-Modem Manuel d'utilisateur
(20 pages)
(20 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.020 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels