ZyXEL omni.net LCD+M Manuel d'utilisateur Page 94
- Page / 186
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Technical Reference for ZyXEL omni.net series
8-6
NOTE: The omni.net LCD/LCD+M does not support network
independent clock compensation. The synchronous timing source
must be supplied by the omni.net LCD/LCD+M , which is phase
locked to the network synchronous clock.
When in V.25bis command mode, the omni.net LCD/LCD+M supports the bit-oriented HDLC
(High-Level Link Control) synchronous protocol which most synchronous communication links
use. Use AT*Ii to enable V.25bis commands. For synchronous applications the TA is set for use
with one application, in normal situations. Save the desired settings in the power-on profile and the
TA will start up in synchronous mode with V.25bis enabled. A special command set RST is
provided to get the TA back to asynchronous AT command mode from V.25bis mode.
When the TA is used as a DCE device with a router or mainframe system, use the following
command string for best results:
AT&S1&M3*I1&W0Z0
- ISDN Terminal Adapters 2
- Limited Warranty 3
- Become a Registered Owner 3
- Contents 5
- PART II ISDN FUNCTION 6
- PART III VOICE FEATURES 7
- PART IV DATA FUNCTION 8
- PART V FAX/MODEM FUNCTION 9
- PART VII APPENDICES 10
- Content of Tables 13
- Content of Figures 17
- Preface 18
- How to Use This Manual 19
- Other References 19
- Part I 21
- Introduction 21
- Chapter 1 23
- Intelligent Features 24
- Specifications 24
- Key Features Summary 25
- Chapter 2 27
- ISDN Configuration Manager 27
- Bumping 31
- Configuring ISDN Parameters 32
- Chapter 3 33
- LCD/LCD+M) 33
- LCD Panel Functions 34
- Right key: 35
- Left key: 35
- Up key: 35
- Down key: 35
- Idle Screen 36
- Set Clock sub-menu 36
- Set Display Mode sub-menu 36
- Dial In Log 37
- Stored Phone List 37
- Dial Out Log 38
- Active Status 39
- Clock Options 40
- Update Clock 41
- Set Display Mode 42
- Dial In Log Options 43
- button 44
- Dial Out Log Options 45
- Part II 47
- ISDN Function 47
- Chapter 4 49
- ISDN Communication Basics 49
- Supported AT Command Types 51
- LCD/LCD+M/Plus) 54
- Placing a Data Call 55
- Incoming Calls 55
- Command Description 58
- ATS119.3=0 58
- ATS119.3=1 58
- Best effort call answering 58
- Part III 61
- Voice Features 61
- Supplementary Service 63
- Chapter 5 63
- Call Waiting 64
- Call Hold/Retrieve 64
- Three Way Conferencing 66
- Starting a conference call 66
- Call Forwarding 68
- For DSS1 switch 68
- Chapter 6 71
- Feature Phone Operation 71
- Flash Key Commands 72
- InterCom 72
- Receiving a Second Call 73
- Call Broker 74
- Call Reject 75
- Call Transfer 75
- Three-Way Conference Call 76
- Last Number Redial 77
- Quick Dial 77
- Part IV 79
- Data Function 79
- Chapter 7 81
- Feature List 82
- Async to Sync Conversion 82
- Authentication Conversion 82
- Multilink PPP 84
- Call Bumping 84
- Bandwidth On Demand (BOD) 86
- BACP/BAP 86
- Chapter 8 89
- ISDN Communications 89
- V.110 Outgoing Protocol 91
- V.120 Outgoing Protocol 92
- X.75 Outgoing Protocol 93
- Speeds of 128Kbps 95
- V.120 Bundled Call 95
- X.75 Bundled Call 97
- Table 52. V.42bis AT Command 98
- Data Compression with X.75 100
- Security Settings 101
- Modifying the User Passwords 105
- Password: 106
- Part V 107
- Fax/Modem Function 107
- Chapter 9 109
- Internal Fax/Modem Function 109
- MNP Protocols 110
- Xmodem, Ymodem, and Zmodem 110
- Fax and Facsimile 111
- Modem as a fax 111
- EIA Class 1 Fax Commands 111
- Answering a Call Using MSN 113
- Control Data Compression 115
- Fax Operation 115
- Fax Command Sets 116
- Appendix D) 118
- Part VI 119
- Diagnostics 119
- Firmware Update 119
- Chapter 10 121
- Power-on Self-test 122
- Resetting Your omni.net 124
- Capturing the Protocol Data 125
- Analyzing the Captured Data 126
- Chapter 11 129
- Firmware Upgrade 129
- Kernel Mode 130
- Part VII 133
- Appendices 133
- Appendix A 135
- AT Command Set Reference 135
- AT Commands Description 136
- AT Commands Prefix (AT) 136
- Description of ATI3 Output 144
- Fax Command 151
- Appendix B 153
- Setting S-registers 154
- S-Register Descriptions 156
- Appendix C 181
- Appendix D 183
- Serial Port Interface 183
Produits connexes et manuels pour Modems ZyXEL omni.net LCD+M
Modems ZyXEL 3356P Manuel d'utilisateur
(30 pages)
(30 pages)
Modems ZyXEL P841C Manuel d'utilisateur
(41 pages)
(41 pages)
Modems ZyXEL P-660M Manuel d'utilisateur
(2 pages)
(2 pages)
Modems ZyXEL ADSL-Modem Manuel d'utilisateur
(20 pages)
(20 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.060 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels