ZyXEL MSAP2000 Manuel d'utilisateur Page 183
- Page / 248
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
183
MSAP2000 AAMS User’s Guide
<atuc ess> <atur
ess>
<atuc fast
rateup> <atur
fast rateup>
<atuc interleave
rateup> <atur
interleave
rateup>
<atuc fast
ratedown> <atur
fast ratedown>
<atuc interleave
ratedown> <atur
interleave
ratedown>
<init fail
enable>
<atuc ses> <atur
ses>
<atuc uas> <atur
uas>
The alarmprofile set command configures ADSL port alarm thresholds. The
MSAP2000 AAMS sends an alarm trap and generates a syslog entry when the
thresholds of the alarm profile are exceeded.
Configure alarm profiles first and then use the alarmprofile map command to set the
MSAP2000 AAMS to use them with specific ADSL ports.
The following example sets an alarm profile named SESalarm that has the
MSAP2000 AAMS send an alarm trap and generate a syslog whenever the
upstream connection’s number of severely errored seconds exceeds three
within a 15 minute period.
Figure 101 Alarm Profile Set Command Example
ras> adsl alarmprofile set SESalarm 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 2 0
3 0 0 0
26.3.16 Alarm Profile Delete Command
Syntax:
adsl alarmprofile delete <profile>
= The number of Errored SecondS that are
permitted to occur within 15 minutes.
= A rate in kilobits per second (kbps). If a fast mode
connection’s upstream transmission rate increases
by more than this number, then a trap is sent.
= A rate in kilobits per second (kbps). If an interleave
mode connection’s upstream transmission rate
increases by more than this number, then a trap is
sent.
= A rate in kilobits per second (kbps). If a fast mode
connection’s downstream transmission rate
decreases by more than this number, then a trap is
sent.
= A rate in kilobits per second (kbps). If an interleave
mode connection’s upstream transmission rate
decreases by more than this number, then a trap is
sent.
= “1” sets the profile to trigger an alarm for an
initialization failure trap. “2” sets the profile to not
trigger an alarm for an initialization failure trap.
= The number of Severely Errored Seconds that are
permitted to occur within 15 minutes.
= The number of UnAvailable Seconds that are
permitted to occur within 15 minutes.
- MSAP2000 1
- Interference Statements and 3
- Warnings 3
- ZyXEL Limited Warranty 5
- Customer Support 6
- Table of Contents 7
- Preface 17
- Computer MSAP2000 Gateway 18
- C HAPTER 1 19
- 1.3 Applications 22
- 1.3.2 Curbside Application 23
- C HAPTER 2 24
- 2.1.1 Front Access Ports 25
- 2.1.2 Front Panel LEDs 26
- 2.1.5 Hardware specification 28
- C HAPTER 3 29
- 3.3 Home Screen 30
- C HAPTER 4 34
- 8 Click VC Setup 36
- 10 Click All and then Apply 37
- 4.3 Default Settings 39
- C HAPTER 5 41
- C HAPTER 6 48
- Basic Setting Screens 48
- 6.3 General Setup 50
- 6.4 IGMP Snooping 52
- 6.5 Switch Setup Screen 53
- C HAPTER 7 57
- 7.4 Interleave Delay 58
- 7.6 Default Settings 59
- 7.7 xDSL Port Setup 59
- 7.7.1 xDSL Port Setting 61
- 7.8 Virtual Channels 62
- 7.9 VC Setup Screen 64
- 7.10 Port Profile Screen 67
- 7.11 ATM QoS 70
- 7.12 Traffic Shaping 70
- 7.12.2 Traffic Parameters 71
- 7.13 VC Profile Screen 72
- 7.14 Alarm Profile Screen 74
- 7.17 Line Performance 80
- 7.17.1 Line Data 81
- C HAPTER 8 84
- 8.3.1 GARP 85
- 8.4 VLAN Status 86
- 8.5 Static VLAN Setting 88
- 8.6 VLAN Port Setting 89
- C HAPTER 9 92
- C HAPTER 10 94
- C HAPTER 11 96
- C HAPTER 12 98
- C HAPTER 13 100
- 13.2 STP Status 102
- 13.2.1 Configure STP 104
- C HAPTER 14 106
- C HAPTER 15 110
- C HAPTER 16 112
- C HAPTER 17 114
- C HAPTER 18 115
- 18.3 About SNMP 116
- 18.3.4 Configuring SNMP 119
- C HAPTER 19 123
- C HAPTER 20 125
- 20.6 Reboot System 127
- 20.7 Command Line FTP 128
- C HAPTER 21 129
- 21.2 Log Format 130
- 21.2.1 Log Messages 131
- ITU-Tís 133
- C HAPTER 22 135
- C HAPTER 23 137
- C HAPTER 24 139
- 24.2 Commands Summary 141
- C HAPTER 25 154
- 25.2 Sys Command Examples 156
- 25.2.4 SNMP Commands 158
- 25.2.15 Date Set Command 163
- 25.2.19 Log Clear Command 165
- C HAPTER 26 168
- 26.3 ADSL Command Examples 173
- 26.3.2 ADSL Enable Command 174
- 26.3.8 ADSL Name Command 178
- 26.3.9 ADSL Tel Command 178
- 3 0 0 0 183
- 26.5 PVC Channels 187
- 26.5.2 PVC Set Command 188
- 26.5.3 PVC Delete Command 189
- C HAPTER 27 190
- 27.2 IGMP Filter Commands 195
- 27.3 DHCP Relay Overview 198
- 27.4 DHCP Relay Commands 198
- 27.7 Filtering Databases 200
- Commands 201
- 27.8.6 VLAN PVID Command 204
- 27.8.7 VLAN Set Command 204
- 27.9 VLAN Enable 209
- 27.10 VLAN Disable 209
- 27.11 MAC Filter Commands 210
- 27.12 MAC Count Commands 213
- C HAPTER 28 218
- 28.3 IP Commands Summary 219
- 28.4 General IP Commands 221
- 28.4.5 Route Show Command 222
- 28.4.6 ARP Show Command 223
- 28.4.7 ARP Flush Command 223
- C HAPTER 29 224
- Syntax: 234
- An example is shown next 234
- C HAPTER 30 235
- C HAPTER 31 237
- C HAPTER 32 241
- 32.5 Local Server 243
- 32.6 Data Rate 244
- 32.7 Configured Settings 244
- 32.8 Password 244
- 32.9 SNMP 244
- 32.10 Telnet 245
- 32.11 Switch Lockout 245
Produits connexes et manuels pour Commutateurs de réseau ZyXEL MSAP2000
(332 pages)
(23 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.362 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels