ZyXEL MSAP2000 Manuel d'utilisateur Page 69
- Page / 248
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
69
MSAP2000 AAMS User’s Guide
Table 18 Port Profile (continued)
LABEL DESCRIPTION
Latency Mode This field sets the ADSL latency mode for the ports that belong to this
profile. Select Fast mode to use no interleaving and have faster
transmission (a “fast channel”). This would be suitable if you have a good
line where little error correction is necessary.
Select Interleave mode to use interleave delay when transmission error correction
(Reed- Solomon) is necessary due to a less than ideal telephone
line. See Section 8.4 on page 84 for more on interleave delay.
Up Stream The following parameters relate to upstream transmissions.
Max Rate Type a maximum upstream transfer rate (32 to 3000 Kbps) for this profile.
(kbps.) Configure the maximum upstream transfer rate to be less than the maximum
downstream transfer rate.
Min Rate Type the minimum upstream transfer rate (32 to 3000 Kbps) for this port.
(kbps.) Configure the minimum upstream transfer rate to be less than the maximum
upstream transfer rate.
Interleave Configure this field when you set the Latency Mode field to Interleave. Type
Delay (ms) the number of milliseconds (1-255) of interleave delay to use for upstream
transfers. It is recommended that you configure the same latency delay for both
upstream and downstream.
Max SNR (db) Type the maximum upstream signal to noise margin (0-31 dB).
Min SNR (db) Type the minimum upstream signal to noise margin (0-31 dB). Configure the
minimum upstream signal to noise margin to be less than or equal to the
maximum upstream signal to noise margin.
Target SNR Type the target upstream signal to noise margin (0-31 dB). Configure the target
(db.) upstream signal to noise margin to be greater than or equal to the minimum
upstream signal to noise margin and less than or equal to the maximum
upstream signal to noise margin.
Down Stream The following parameters relate to downstream transmissions.
Max Rate Type a maximum downstream transfer rate (32 to 25000 Kbps) bps for this port.
(kbps.) Configure the maximum downstream transfer rate to be greater than the maximum
upstream transfer rate.
Min Rate Type the minimum downstream transfer rate (32 to 25000 Kbps) for this port.
(Kbps.) Configure the minimum downstream transfer rate to be less than the maximum
downstream transfer rate.
Interleave Configure this field when you set the Latency Mode field to interleave. Type the
Delay (ms) number of milliseconds (1-255) of interleave delay to use for upstream transfers. It
is recommended that you configure the same latency delay for both upstream and
downstream.
Max SNR (db) Type the maximum downstream signal to noise margin (0-31 dB).
Min SNR (db) Type the minimum downstream signal to noise margin (0-31 dB). Configure
the minimum downstream signal to noise margin to be less than or equal to
the maximum downstream signal to noise margin.
Target SNR Type the target downstream signal to noise margin (0-31 dB). Configure the target
(db) downstream signal to noise margin to be greater than or equal to the minimum
downstream signal to noise margin and less than or equal to the maximum
downstream signal to noise margin.
Add
Cancel Click Cancel to start configuring the screen again.
Click
A
dd to save you
r
changes
t
o the AAM’s vola
t
ile memo
r
y
. The AAM loses
these changes if it is turned off or loses power, so use the Config Save link on
the navigation panel to save your changes to the non-volatile memory when
you are done configuring.
- MSAP2000 1
- Interference Statements and 3
- Warnings 3
- ZyXEL Limited Warranty 5
- Customer Support 6
- Table of Contents 7
- Preface 17
- Computer MSAP2000 Gateway 18
- C HAPTER 1 19
- 1.3 Applications 22
- 1.3.2 Curbside Application 23
- C HAPTER 2 24
- 2.1.1 Front Access Ports 25
- 2.1.2 Front Panel LEDs 26
- 2.1.5 Hardware specification 28
- C HAPTER 3 29
- 3.3 Home Screen 30
- C HAPTER 4 34
- 8 Click VC Setup 36
- 10 Click All and then Apply 37
- 4.3 Default Settings 39
- C HAPTER 5 41
- C HAPTER 6 48
- Basic Setting Screens 48
- 6.3 General Setup 50
- 6.4 IGMP Snooping 52
- 6.5 Switch Setup Screen 53
- C HAPTER 7 57
- 7.4 Interleave Delay 58
- 7.6 Default Settings 59
- 7.7 xDSL Port Setup 59
- 7.7.1 xDSL Port Setting 61
- 7.8 Virtual Channels 62
- 7.9 VC Setup Screen 64
- 7.10 Port Profile Screen 67
- 7.11 ATM QoS 70
- 7.12 Traffic Shaping 70
- 7.12.2 Traffic Parameters 71
- 7.13 VC Profile Screen 72
- 7.14 Alarm Profile Screen 74
- 7.17 Line Performance 80
- 7.17.1 Line Data 81
- C HAPTER 8 84
- 8.3.1 GARP 85
- 8.4 VLAN Status 86
- 8.5 Static VLAN Setting 88
- 8.6 VLAN Port Setting 89
- C HAPTER 9 92
- C HAPTER 10 94
- C HAPTER 11 96
- C HAPTER 12 98
- C HAPTER 13 100
- 13.2 STP Status 102
- 13.2.1 Configure STP 104
- C HAPTER 14 106
- C HAPTER 15 110
- C HAPTER 16 112
- C HAPTER 17 114
- C HAPTER 18 115
- 18.3 About SNMP 116
- 18.3.4 Configuring SNMP 119
- C HAPTER 19 123
- C HAPTER 20 125
- 20.6 Reboot System 127
- 20.7 Command Line FTP 128
- C HAPTER 21 129
- 21.2 Log Format 130
- 21.2.1 Log Messages 131
- ITU-Tís 133
- C HAPTER 22 135
- C HAPTER 23 137
- C HAPTER 24 139
- 24.2 Commands Summary 141
- C HAPTER 25 154
- 25.2 Sys Command Examples 156
- 25.2.4 SNMP Commands 158
- 25.2.15 Date Set Command 163
- 25.2.19 Log Clear Command 165
- C HAPTER 26 168
- 26.3 ADSL Command Examples 173
- 26.3.2 ADSL Enable Command 174
- 26.3.8 ADSL Name Command 178
- 26.3.9 ADSL Tel Command 178
- 3 0 0 0 183
- 26.5 PVC Channels 187
- 26.5.2 PVC Set Command 188
- 26.5.3 PVC Delete Command 189
- C HAPTER 27 190
- 27.2 IGMP Filter Commands 195
- 27.3 DHCP Relay Overview 198
- 27.4 DHCP Relay Commands 198
- 27.7 Filtering Databases 200
- Commands 201
- 27.8.6 VLAN PVID Command 204
- 27.8.7 VLAN Set Command 204
- 27.9 VLAN Enable 209
- 27.10 VLAN Disable 209
- 27.11 MAC Filter Commands 210
- 27.12 MAC Count Commands 213
- C HAPTER 28 218
- 28.3 IP Commands Summary 219
- 28.4 General IP Commands 221
- 28.4.5 Route Show Command 222
- 28.4.6 ARP Show Command 223
- 28.4.7 ARP Flush Command 223
- C HAPTER 29 224
- Syntax: 234
- An example is shown next 234
- C HAPTER 30 235
- C HAPTER 31 237
- C HAPTER 32 241
- 32.5 Local Server 243
- 32.6 Data Rate 244
- 32.7 Configured Settings 244
- 32.8 Password 244
- 32.9 SNMP 244
- 32.10 Telnet 245
- 32.11 Switch Lockout 245
Produits connexes et manuels pour Commutateurs de réseau ZyXEL MSAP2000
(332 pages)
(23 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.344 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels